Regviz

Freescale Semiconductor /MKL02Z4 /PORTA /PCR24

Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text

Interpret as PCR24

Share

Cut and paste this URL to share the unmodified register and value:

https://regviz.com/r/Freescale Semiconductor/MKL02Z4/PORTA/PCR24#0x0

31 2827 2423 2019 1615 1211 87 43 0 0 0 0 0 0 0 0 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 (0)PE 0 (0)PFE 0 (0)DSE 0 (000)MUX0 (0000)IRQC0 (0)ISF

IRQC=0000, MUX=000, DSE=0, ISF=0, PE=0, PFE=0

Description

Pin Control Register n

Fields

PE

Pull Enable

0 (0): Internal pullup or pulldown resistor is not enabled on the corresponding pin.

1 (1): Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input.
PFE

Passive Filter Enable

0 (0): Passive input filter is disabled on the corresponding pin.

1 (1): Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics.
DSE

Drive Strength Enable

0 (0): Low drive strength is configured on the corresponding pin, if pin is configured as a digital output.

1 (1): High drive strength is configured on the corresponding pin, if pin is configured as a digital output.
MUX

Pin Mux Control

0 (000): Pin disabled (analog).

1 (001): Alternative 1 (GPIO).

2 (010): Alternative 2 (chip-specific).

3 (011): Alternative 3 (chip-specific).

4 (100): Alternative 4 (chip-specific).

5 (101): Alternative 5 (chip-specific).

6 (110): Alternative 6 (chip-specific).

7 (111): Alternative 7 (chip-specific).
IRQC

Interrupt Configuration

0 (0000): Interrupt request disabled.

8 (1000): Interrupt when logic zero.

9 (1001): Interrupt on rising edge.

10 (1010): Interrupt on falling edge.

11 (1011): Interrupt on either edge.

12 (1100): Interrupt when logic one.
ISF

Interrupt Status Flag

0 (0): Configured interrupt is not detected.

1 (1): Configured interrupt is detected. The flag remains set until a logic one is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared.

Links

()

Register License

Redistribution and use in source and binary forms, with or without modification,\nare permitted provided that the following conditions are met:\n o Redistributions of source code must retain the above copyright notice, this list\n of conditions and the following disclaimer.\n o Redistributions in binary form must reproduce the above copyright notice, this\n list of conditions and the following disclaimer in the documentation and/or\n other materials provided with the distribution.\n o Neither the name of Freescale Semiconductor, Inc. nor the names of its\n contributors may be used to endorse or promote products derived from this\n software without specific prior written permission.\n THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND\n ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED\n WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE\n DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR\n ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES\n (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;\n LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON\n ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT\n (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS\n SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

 ()

Register Reference

https://github.com/cmsis-svd/cmsis-svd-data